12V 2A switching power supply medical equipment power supply module constant voltage CE 24W security monitoring power supply

>> Projector/Stage/Medical light source&Driver

12V 2A switching power supply medical equipment power supply module constant voltage CE 24W security monitoring power supply

12V 2A switching power supply medical equipment power supply module constant voltage CE 24W security monitoring power supply

Technical Parameters:

	Model No.:	MOL-U20S5H	MOL-U20S12H	MOL-U20S17.5H	MOL-U20S24H
Output characteristics	Output Voltage	5V	12V	17.5V	24V
	Rated current	3000mA	2000mA	1200mA	1000mA
	Current range	0-3000mA	0-2000mA	0-1200mA	0-1000mA
	Ripple	<100 mVp-p	<100 mVp-p	<80 mVp-p	<100 mVp-p
	Output Precision	±1%	±1%	±1%	±1%
	Voltage regulation rate	<±1%	<±1%	<±1%	<±1%
	load Adjustment rate	±1.2%	±1.2%	±1.2%	±1.2%
	Rated Power	15W	24W	21W	24W
	Adjustable output range	4.2-6.2V	10.5-14V	15-20V	21.5-26.5V
	Build, rise, hold time	50ms, 30ms, 30ms/24VDC
Input characteristics	Input voltage range	AC85V-265V
	Input Current	0.05A-0.3A
	Frequency Range	50HZ-60HZ
	Efficiency (determined according to input voltage)	>76%	>82%	>83%	>85%
	Starting impulse current	cold start <0.30A
	Leakage current	<0.6mA/220VAC
Protection characteristics	Over power protection	130-150% rated power,Automatic recovery after fault removal
	Overvoltage protection	DCOUT >130%
	Output short circuit protection	power supply Intermittent Gap,Power recovery after Eliminate short circuits
Over temperature protection	close control when PWM chip node temperature>100℃
Environmental parameters	Working temperature, humidity	_20℃ - +60℃ @100% load, +60℃ @60% load; 20%-90% RH
Environmental parameters	Storage temperature, humidity	_40℃- +105℃ 10%-95% RH
Safety and EMC standards	EMI safety standards	GB17625.2; GB17626.4; En55022 CLASSB
	Withstand voltage	I/P-O/P:3.0KVAC 1min
	Insulation resistance	I/P-O/P: 500VDC/100M Ohms
Other	Dimension	76x40x23.5mm
Other	Weight	39g
Remarks	1.All technical parameters are measured under the condition of 220VAC input,Rated load environment 25℃, Humidity 70%.
	2.Precision: Including setting tolerance, voltage adjustment rate, load adjustment rate.
	3.Ripple test: Use the twisted wire of 30cm to connect power supply and load,
	0.1uF and 47uF capacitors on the load side,Measured with a 20MH oscilloscope at the load end.
	4.Voltage regulation rate: Under rated load conditions, the input voltage is measured from low to high.
	5.Load Regulation rate:The measured output changes from 0% load to 100% load.
	6.Every line Can output maximum current, But the total load cannot exceed the maximum output power.

Dimension:

Inquiry

We are exporting LED prodcuts to all over the world, please don’t hesitate to contact us for any inquiry or suggestion, and you will receive our prompt reply within 24 working hours.

Subject:

E-mail:

Tel:

Message:

Verify Code: