12V 1.7A switching power supply module 20W low power consumption and high efficiency monitoring LED driver board

>> Projector/Stage/Medical light source&Driver

12V 1.7A switching power supply module 20W low power consumption and high efficiency monitoring LED driver board

12V 1.7A switching power supply module 20W low power consumption and high efficiency monitoring LED driver board

Technical Parameters:

	Model No.:	MOL-18S05300WR	MOL-18S09200WR	MOL-18S12170WR	MOL-18S15120WR	MOL-18S24083WR	MOL-18S36055WR
Output characteristics	Output Voltage	5V	9V	12V	15V	24V	36V
	Rated current	3A	2A	1.7A	1.35A	0.83A	0.55A
	Current range	0-3.5A	0-2.0A	0-1.7A	0-1.4A	0-0.83A	0-0.55A
	Ripple	<80mVp-p	<80mVp-p	<100mVp-p	<100mVp-p	<150mVp-p	<200mVp-p
	Output voltage range	4.95-5.2V	8.9-9.1V	11.9-12.1V	14.9-15.1V	23.9-24.1V	35.8-36.2V
	Voltage regulation rate	±1.1%	±1.1%	±1.1%	±1.1%	±1.1%	±1.1%
	load Adjustment rate	±1.5%	±1.5%	±1.5%	±1.5%	±1.5%	±1.5%
	Rated Power	17.5W	18W	20.4W	20.25W	20W	20W
	Build, rise, hold time	300ms, 20ms, 20ms/220VAC
Input characteristics	Input voltage range	90-264V AC (DC125V-375VDC)
	Input Current	<0.2A (Average current 0.03-0.1A)
	Frequency Range	47-63HZ
	No-load power consumption	220VAC IN: <0.3W; 110VAC IN:<0.1W
	Starting impulse current	cold start <30A/230VAC IN
	Leakage current	<3mA/220VAC
Protection characteristics	Over power protection	150-170% rated power,Automatic recovery after fault removal
	Overvoltage protection	VH1:>50%
	DC short circuit protection	power supply Intermittent Gap,Power recovery after Eliminate short circuits
Environmental parameters	Working temperature, humidity	_20℃ - +40℃ @100% load, +60℃ @60% load; 20%-90% RH
Environmental parameters	Storage temperature, humidity	_30℃- +85℃ 10%-95% RH
Safety and EMC standards	safety standards	EN55032:2015; En55024:2010+ EN61000-3-2
	Withstand voltage	I/P-O/P:3KVAC 1min
	Insulation resistance	I/P-O/P: 500VDC/100M Ohms
Other	Dimension	50x36x21mm
Other	Weight	35g
Remarks	1.All technical parameters are measured under the condition of 220VAC input, Rated load environment 25℃, Humidity 70%.
	2.Precision: Including setting tolerance, voltage adjustment rate, load adjustment rate.
	3.Ripple test: Use the twisted wire of 30cm to connect power supply and load,
	0.1uF and 47uF capacitors on the load side, Measured with a 20MH oscilloscope at the load end.
	4.Voltage regulation rate: Under rated load conditions, the input voltage is measured from low to high.
	5.Load Regulation rate: The measured output changes from 0% load to 100% load.
	6.Every line Can output maximum current, but the total load cannot exceed the maximum output power.

Inquiry

We are exporting LED prodcuts to all over the world, please don’t hesitate to contact us for any inquiry or suggestion, and you will receive our prompt reply within 24 working hours.

Subject:

E-mail:

Tel:

Message:

Verify Code: